Cluster
contains the settings to specify details
about a cluster, such as its interface, IP address, portrules,
and so on.
Note |
---|
To enable this Network Load Balancing setting, the NetworkLoadBalancingFullServer package must be enabled in the Windows® image you are installing. To do this, use Windows System Image Manager to add the Microsoft-Windows-Foundation-Package to your answer file, and then configure the NetworkLoadBalancingFullServer package to enable it. For more information about adding and configuring packages, see the Windows® Assessment and Deployment (Windows ADK) Technical Reference. |
Child Elements
Specifies details about a bidirectional affinity (BDA) team. |
|
Specifies the cluster primary IP address. |
|
Specifies whether the cluster MAC address is automatically calculated from the primary cluster IP address. |
|
Specifies the cluster MAC address to be used when configuring a unicast cluster. |
|
Specifies the mode for the cluster. |
|
Specifies a full Internet name for the cluster. |
|
Specifies the subnet mask for the cluster IP address. |
|
Specifies the host's unique IP addresses. |
|
Specifies the host identifier used by this cluster. |
|
Specifies whether Internet Control Message Protocol (ICMP) filtering is enabled for the cluster. |
|
Specifies the recurrence interval for transmitting identity heartbeats between the NetworkLoadBalancing cluster hosts. |
|
Specifies the initial host state for the cluster. |
|
Specifies the interface name to bind to network load balancing (NLB). This is a required setting. |
|
Specifies whether source Media Access Control (MAC) address masking is used. |
|
Specifies the maximum number of descriptors per allocation for the cluster. |
|
Specifies the number of lost heartbeat messages before Setup considers the Network Load Balancing cluster host inactive and initiates convergence. |
|
Specifies a period between sending Network Load Balancing cluster heartbeat messages. |
|
Specifies whether address resolution protocol (ARP) traffic should be spoofed. |
|
Specifies whether NetBT support is enabled for the cluster. |
|
Specifies whether a host that is shut down while in a suspended state will remain suspended when Windows® is started. |
|
Specifies details about the port rules that are used for the cluster, including a port rule's name, virtual IP address, protocol, mode, and so on. |
|
Specifies whether unicast, interhost communication support is enabled for the cluster. |
|
Specifies the cluster’s virtual IP addresses. |
Valid Configuration Passes
specialize
Parent Hierarchy
Microsoft-Windows-NetworkLoadBalancing-Core | Clusters | Cluster
Applies To
For a list of the Windows editions and architectures that this component supports, see Microsoft-Windows-NetworkLoadBalancing-Core.
XML Example
The following XML output shows how to specify details about a cluster.
Copy Code | |
---|---|
<Cluster> <Interface>Local Area Connection 2</Interface> <ClusterIpAddress>10.100.0.234</ClusterIpAddress> <ClusterNetMask>255.255.255.0</ClusterNetMask> <VirtualIpAddresses> <IpAddress wcm:keyValue="Ip1"> <IpAddress>10.192.45.1</IpAddress> <NetworkMask>255.255.255.0</NetworkMask> </IpAddress> <IpAddress wcm:keyValue="Ip2"> <IpAddress>fe80::204:23ff:feb9:1111</IpAddress> </IpAddress> </VirtualIpAddresses> <Portrules> <Portrule wcm:keyValue="Portrule1"> <VirtualIpAddress>255.255.255.255</VirtualIpAddress> <Protocol>TCP</Protocol> <StartPort>0</StartPort> <EndPort>65535</EndPort> <Mode>MultipleHost</Mode> <EqualLoad>true</EqualLoad> <ClientAffinity>None</ClientAffinity> </Portrule> <Portrule wcm:keyValue="Portrule2"> <VirtualIpAddress>10.100.0.223</VirtualIpAddress> <Protocol>Both</Protocol> <StartPort>80</StartPort> <EndPort>80</EndPort> <Mode>MultipleHost</Mode> <LoadWeight>100</LoadWeight> <ClientAffinity>Single</ClientAffinity> </Portrule> <Portrule wcm:keyValue="Portrule3"> <VirtualIpAddress>10.100.0.99</VirtualIpAddress> <Protocol>TCP</Protocol> <StartPort>23</StartPort> <EndPort>23</EndPort> <Mode>Disabled</Mode> </Portrule> <Portrule wcm:keyValue="Portrule4"> <VirtualIpAddress>255.255.255.255</VirtualIpAddress> <Protocol>UDP</Protocol> <StartPort>25</StartPort> <EndPort>25</EndPort> <Mode>MultipleHost</Mode> <EqualLoad>true</EqualLoad> <ClientAffinity>Network</ClientAffinity> </Portrule> <Portrule wcm:keyValue="Portrule5"> <VirtualIpAddress>10.100.0.223</VirtualIpAddress> <Protocol>TCP</Protocol> <StartPort>3389</StartPort> <EndPort>3389</EndPort> <Mode>SingleHost</Mode> <HostPriority>1</HostPriority> </Portrule> </Portrules> <DedicatedIpAddresses> <IpAddress wcm:keyValue="Ip1"> <IpAddress>10.192.45.1</IpAddress> <NetworkMask>255.255.255.0</NetworkMask> </IpAddress> <IpAddress wcm:keyValue="Ip2"> <IpAddress>fe80::204:23ff:feb9:1111</IpAddress> </IpAddress> </DedicatedIpAddresses> <HostIdentifier>6</HostIdentifier> <ClusterMacAddress>02-bf-01-02-03-04</ClusterMacAddress> <ClusterName>mycluster.domain.com</ClusterName> <ClusterMode>Multicast</ClusterMode> <InitialHostState>Started</InitialHostState> <PersistSuspendedState>false</PersistSuspendedState> <MembershipHeartbeatPeriod>1000</MembershipHeartbeatPeriod> <MembershipHeartbeatLossTolerance>5</MembershipHeartbeatLossTolerance> <IdentityHeartbeatPeriod>2000</IdentityHeartbeatPeriod> <MulticastSpoofEnabled>false</MulticastSpoofEnabled> <MaskSourceMacEnabled>true</MaskSourceMacEnabled> <ICMPFilteringEnabled>false</ICMPFilteringEnabled> <NetBTSupportEnabled>true</NetBTSupportEnabled> <ClusterIpToClusterMacEnabled>true</ClusterIpToClusterMacEnabled> <UnicastInterHostCommunicationSupportEnabled>true</UnicastInterHostCommunicationSupportEnabled> <MaximumConnectionDescriptors>512</MaximumConnectionDescriptors> <BDATeam> <Team>{BF967924-0DE6-11D0-A285-00AA003049E2}</Team> <Master>true</Master> <ReverseHash>true</ReverseHash> </BDATeam> </Cluster> |